Find help with bricklaying and rendering around Pakenham.

Weep holes and damp brick walls

How weep holes and damp-proof courses keep Pakenham 3810 brick veneer walls dry.

Most Pakenham 3810 homes built since the 1970s are brick veneer, with a narrow cavity between the brick skin and the frame. Weep holes, flashings and a damp-proof course keep that cavity draining and the wall dry. When they are blocked or bridged, damp, salt and mould follow. This guide explains how the system works and what goes wrong.

How a brick veneer wall manages water

Brick is porous. In heavy, wind-driven rain, water soaks into the outer brick skin and some reaches the inside face. A brick veneer wall is designed for this. The cavity separates the brick from the timber or steel frame, and any water that gets through runs down the back of the brick to the bottom of the cavity.

At the base of the wall, and above windows and doors, flashings catch that water and direct it outward. Weep holes in the brickwork just above the flashings let it drain out. The cavity also allows air to move, helping the brick dry.

Double brick walls work on a similar principle, with a cavity between two brick skins, flashings at the base and over openings, and weep holes to drain the cavity.

What are weep holes?

Weep holes are small openings in the outer brick skin, usually an empty vertical mortar joint (a perpend) left open at regular intervals. You will find them:

  • In the course just above the base flashing, near ground or slab level
  • Above window and door heads, over the lintel flashing
  • Above some roof junctions where a lower roof meets a brick wall

They are easy to overlook. They are often a single open joint every few bricks, sometimes fitted with a plastic insert. Their spacing and position follow building standards and the manufacturer’s details for the wall system.

What is the damp-proof course?

The damp-proof course, or DPC, is a waterproof layer built into a brick wall near its base. It stops moisture in the ground rising up through the bricks by capillary action. In older homes it may be slate, bitumen-coated material or lead. In newer homes it is usually a polyethylene membrane, often combined with the base flashing in veneer walls.

You can often spot the DPC as a thin line in a mortar joint a few courses above ground level, or just above the slab edge. Anything that lets moisture go around it, such as soil, render or paving above it, defeats its purpose. This is called bridging.

Common ways the system fails

Problem How it happens What you may see
Weep holes covered by soil or mulch Garden beds built up against the wall Damp patches inside near floor level, musty smell
Weep holes covered by paving New paving laid higher than the original ground Efflorescence, damp skirting boards
Weep holes filled with mortar Cosmetic repairs or careless repointing Water trapped in cavity, staining above openings
Weep holes rendered over Render applied without leaving openings Damp inside, render staining and drummy patches
DPC bridged by render Render taken down to the ground Rising damp, salt marks above ground level
Cavity bridged by mortar droppings Mortar falls into cavity during construction Damp spots inside at one location
Missing or damaged flashings Poor workmanship or later alterations Leaks around windows and doors
Raised ground after landscaping Lawn, soil or paths built up over time Damp, termite risk, efflorescence

Raised ground and paving are among the most common causes on Pakenham homes. Landscaping after a new home is handed over often lifts the ground level against the walls, especially on estate lots in Officer and Clyde North. The Officer area page discusses this.

Signs of damp in brick walls

Watch for:

  1. White powdery deposits on brick faces near the base of walls (efflorescence)
  2. Flaking or crumbling bricks, especially low on the wall
  3. Dark damp patches that remain after rain stops
  4. Moss and algae growth on the lower courses
  5. Peeling paint, bubbling plaster or swollen skirting boards inside
  6. A musty smell in rooms on the affected side
  7. Mould on internal walls near floor level

Some of these can also come from other sources, such as a leaking pipe inside a wall or condensation from poor ventilation. A provider can help pinpoint the cause.

Termites and covered weep holes

Covered weep holes and bridged slab edges are also a termite concern. Many homes rely on a visible slab edge or termite management system near the base of the wall, so inspectors can see termite activity. Soil, mulch and paving over the slab edge and weep holes create hidden entry routes. If you have a termite management system, check its requirements before landscaping. A licensed pest controller can advise on inspections.

Fixing common damp problems

Many damp problems can be fixed by restoring the original design:

  • Lower garden beds and soil so they sit below the DPC and weep holes
  • Pull mulch and plants back from the base of walls
  • Cut back paving or regrade it to fall away from the house, or install a drain alongside the wall
  • Clear blocked weep holes carefully without pushing debris into the cavity
  • Cut back render that bridges the DPC and finish it above the damp line
  • Fix leaking taps, pipes, gutters and downpipes near the wall
  • Improve sub-floor ventilation by clearing vents

Some problems need more work, such as removing mortar droppings from the cavity, replacing damaged flashings or installing a new DPC in an older wall. These are jobs for a bricklayer or specialist. The brickwork repairs page covers replacing damaged bricks, and the brick cleaning and efflorescence page covers salt deposits.

Older homes without a cavity

Some older homes in the Pakenham township, Beaconsfield and rural areas have solid brick walls or early cavity walls with different details. Their DPC may have deteriorated, and the mortar may be soft and lime based. Treating rising damp in these walls needs care. Methods include chemical DPC injection, physical DPC insertion and improving drainage and ventilation. Get advice from a provider experienced with older masonry. The Beaconsfield area page discusses older housing there.

New work: getting it right first time

If you are building a new brick wall, extension or opening, ask the provider how they will handle weep holes, flashings and the DPC. Points to confirm:

  • Weep holes will be installed above all base and opening flashings
  • The cavity will be kept clear of mortar droppings
  • Flashings will be correctly lapped and sealed at junctions
  • Render will finish above the DPC and leave weep holes open
  • Finished ground and paving levels will sit below the DPC

The extension brickwork page and the openings and alterations page cover these details for building work.

Local conditions around Pakenham

Pakenham’s wet winters test wall drainage every year. Low-lying land toward the former Koo Wee Rup swamp and near creeks stays wet longer. Clay soils hold water close to footings. Sloping blocks in the hills send runoff against uphill walls. Each of these increases the load on weep holes and DPCs.

During heavy rain, walk around your house and watch where water flows and pools. Note which walls stay damp longest. That information helps any provider diagnose a damp problem.

Weep holes and pests

Weep holes are open joints, so insects, spiders and occasionally small animals use them. Some owners respond by filling them with mortar, silicone or expanding foam, which stops the wall draining. Purpose-made weep hole covers allow water and air through while keeping out larger pests. They are usually a vented plastic or stainless steel insert pushed into the open joint. If you fit covers, check them occasionally for blockages from dust and spider webs, and make sure they do not sit lower than the flashing they serve.

Condensation and ventilation inside

Not every damp wall is caused by water from outside. In cold weather, warm moist air from cooking, showers and drying clothes can condense on the inside of cold external walls, especially behind furniture and in corners with little airflow. The result looks like damp: mould spots, peeling paint and a musty smell. The difference is that condensation is usually worst in winter mornings and in rooms with poor ventilation, and does not follow rain events.

Before paying for masonry repairs, rule out condensation by improving ventilation, using exhaust fans that vent outside, and moving furniture slightly away from external walls. If damp persists after that, or follows rain, the wall itself is the more likely source.

Damp in garages and outbuildings

Garages, sheds and outbuildings often show damp first because they are less carefully detailed than the house. Slabs may be poured level with the ground outside, walls may be single-skin brick or block with no cavity, and water from driveways can run straight against the base. Efflorescence, flaking paint and rusting tools are common signs. Fixes include regrading the ground so water runs away, adding a strip drain at the door, sealing the slab edge and improving ventilation. Single-skin masonry walls can be treated with breathable water repellents designed for masonry, although they will not stop water rising from the ground. A provider can suggest what suits the building.

Weep holes when paving or decking is added

Adding paving, a deck or an alfresco slab next to a brick wall is one of the most common ways weep holes and damp-proof courses get covered. Before you build, mark the damp-proof course and weep holes on the wall with chalk so the landscaper or builder can see them. Paving should finish below them and fall away from the house. A deck can be built at a level that leaves a gap above the ground and below the weep holes, with ventilation underneath. Where finished levels cannot sit low enough, a strip drain with a grate along the wall can carry water away and keep the base of the wall clear. Agreeing this before work starts costs far less than lifting new paving later.

Ask a local provider

If you suspect blocked weep holes, a bridged DPC or damp brick walls, describe the problem on the damp wall enquiry form. Include photos of the base of the wall, the ground level and any damp signs inside. Up to three independent providers in the area may receive your request and choose to contact you. They assess the cause and quote on their own terms. Yes Right Pty Ltd operates this referral site; we do not inspect or repair walls.

Send an enquiry